Siemens ET 200SP AI Energy Meter CT ST; 6ES7134-6PA01-0BU0
SIMATIC ET 200SP, analog input module, AI Energy Meter CT ST, for 1A or 5A current transformer, suitable for BU type U0, channel diagnostics...
Price on request
| SIMATIC ET 200SP, analog input module, AI Energy Meter CT ST, for 1A or 5A current transformer, suitable for BU type U0, channel diagnostics |
| General information | |
| Product type designation | AI Energy Meter CT ST |
| Firmware version | V8.0 |
| ● FW update possible | Yes |
| usable BaseUnits | BU type U0 |
| Color code for module-specific color identification plate | CC20 |
| Supported power supply systems | TT, TN, IT |
| Product function | |
| ● Voltage measurement | Yes |
| — without voltage transformer | Yes |
| — with voltage transformer | Yes |
| ● Current measurement | Yes; max. 3 + neutral conductor |
| — without current transformer | No |
| — with current transformer | Yes; 1 A or 5 A current transformer |
| — With Rogowski coil | No |
| — With current-voltage-converter | No |
| ● Energy measurement | Yes |
| ● Frequency measurement | Yes |
| ● Power measurement | Yes |
| ● Active power measurement | Yes |
| ● Reactive power measurement | Yes |
| ● Power factor measurement | Yes |
| ● Active factor measurement | Yes |
| ● Reactive power compensation | Yes |
| ● Line analysis | No |
| ● I&M data | Yes; I&M0 to I&M3 |
| ● Isochronous mode | No |
| Engineering with | |
| ● STEP 7 TIA Portal configurable/integrated from version | STEP 7 V16 or higher with HSP |
| ● STEP 7 configurable/integrated from version | Configurable via GSD file |
| ● PROFIBUS from GSD version/GSD revision | One GSD file each, Revision 3 and 5 and higher |
| ● PROFINET from GSD version/GSD revision | V2.3 |
| Operating mode | |
| ● Switching between operating modes in RUN | Yes; For module version 32 I/20 Q, it is possible to dynamically switch between 25 user data variants, 23 of which are pre-defined and 2 of which can be defined by the specific user |
| ● Cyclic measured value access | Yes |
| ● Acyclic measured value access | Yes |
| ● Fixed measured value sets | Yes |
| ● Freely definable measured value sets | Yes; For cyclic and acyclic measured value access |
| CiR - Configuration in RUN | |
| Reparameterization possible in RUN | Yes |
| Calibration possible in RUN | Yes |
| Installation type/mounting | |
| Mounting position | any |
| Supply voltage | |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Input current | |
| Current consumption (rated value) | 12.5 mA |
| Current consumption, max. | 17 mA |
| Power loss | |
| Power loss, typ. | 1 W; 3x 5 A input current, 3x 230 V AC |
| Address area | |
| Address space per module | |
| ● Inputs | 256 byte |
| ● Outputs | 20 byte |
| Hardware configuration | |
| Automatic encoding | Yes |
| ● Mechanical coding element | Yes |
| ● Type of mechanical coding element | type C |
| Selection of BaseUnit for connection variants | |
| ● 2-wire connection | BU type U0 |
| Time of day | |
| Operating hours counter | |
| ● present | Yes |
| Analog inputs | |
| Cycle time (all channels), typ. | 50 ms; Time for consistent update of all measured and calculated values (cyclic und acyclic data) |
| Cable length | |
| ● shielded, max. | 200 m |
| ● unshielded, max. | 200 m |
| Analog value generation for the inputs | |
| Sampling frequency, max. | 2 048 kHz |
Similar products:
Siemens ET 200SP, F-AI 4xU 0..10V HF; 6ES7136-6AB00-0CA1
SIMATIC DP, electronics module ET 200SP, F-AI 4xU 0..10V HF, fail-safe analog inputs, up to PL E (ISO 13849), up to SIL 3 (IEC 61508)
-
(Out of stock)
Price on request
Siemens ET 200SP AI 2 X SG 4-/6-WIRE HS; 7MH4134-6LB00-0DA0
SIMATIC ET 200SP, ANALOG INPUT MODULE, AI 2 X SG 4-/6-WIRE HIGH SPEED, FITS TO BU-TYPE A0, COLOR CODE CC00, CHANNEL DIAGNOSIS, 28/16BIT, +/-0,05%, FOR STRAIN GAUGE
-
(Out of stock)
Price on request
Siemens ET 200SP, AI 4xRTD/TC 2-/3-/4-Wire HF; 6ES7134-6JD00-0CA1
SIMATIC ET 200SP, Analog input module, AI 4xRTD/TC High Feature, suitable for BU type A0, A1, Color code CC00, channel diagnostics, 16 bit, +/-0.1%, 2-/3-/4-wir
-
(Out of stock)
Price on request
Siemens ET 200SP, AI 4xU/I 2-Wire ST, PU 1; 6ES7134-6HD01-0BA1
SIMATIC ET 200SP, ANALOG INPUT MODULE, AI 4XU/I 2-WIRE STANDARD, PACKING UNIT: 1 PIECE, FITS TO BU-TYPE A0, A1, COLOR CODE CC03, MODULE DIAGNOSIS, 16BIT, +/-0,3
-
(Out of stock)
Price on request
Siemens ET 200SP, F-AI 4XI (0)4..20mA HF; 6ES7136-6AA00-0CA1
SIMATIC DP, ELECTRONIC MODULE ET 200SP, F-AI 4xI(0)4..20mA HF FAILSAFE ANALOG INPUTS up to PL E (ISO 13849) up to SIL 3 (IEC 61508)
-
(Out of stock)
Price on request
Siemens ET 200SP, AI 2xI 2-/4-Wire ST, PU 1; 6ES7134-6GB00-0BA1
SIMATIC ET 200SP, Analog input module, AI 2xI 2-/4-wire Standard, Pack quantity: 1 unit, suitable for BU type A0, A1, Color code CC05, Module diagnostics, 16 bi
-
(Out of stock)
18.203,76