Siemens ET 200SP AI Energy Meter RC HF; 6ES7134-6PA21-0CU0
SIMATIC ET 200SP, analog input module, AI Energy Meter RC HF, for Rogowski coils or current/voltage transformer 333 mV, with network analysis functions, suitable...
Price on request
SIMATIC ET 200SP, analog input module, AI Energy Meter RC HF, for Rogowski coils or current/voltage transformer 333 mV, with network analysis functions, suitable for BU type U0, channel diagnostics |
General information | |
Product type designation | AI Energy Meter RC HF |
Firmware version | V8.0 |
● FW update possible | Yes |
usable BaseUnits | BU type U0 |
Color code for module-specific color identification plate | CC20 |
Supported power supply systems | TT, TN, IT |
Product function | |
● Voltage measurement | Yes |
— without voltage transformer | Yes |
— with voltage transformer | Yes |
● Current measurement | Yes; Max. 4 |
— without current transformer | No |
— with current transformer | No |
— With Rogowski coil | Yes |
— With current-voltage-converter | Yes; 333 mV interface |
● Energy measurement | Yes |
● Frequency measurement | Yes |
● Power measurement | Yes |
● Active power measurement | Yes |
● Reactive power measurement | Yes |
● Power factor measurement | Yes |
● Active factor measurement | Yes |
● Reactive power compensation | Yes |
● Line analysis | Yes |
— Monitoring of instantaneous and half-wave values | Yes |
— THD measurement for current and voltage | Yes |
— Harmonics for current and voltage | Yes |
— Voltage dip (DIP) | Yes |
— Voltage swell | Yes |
● I&M data | Yes; I&M0 to I&M3 |
● Isochronous mode | No |
Engineering with | |
● STEP 7 TIA Portal configurable/integrated from version | STEP 7 V16 or higher with HSP |
● STEP 7 configurable/integrated from version | V5.5 SP3 or higher |
● PROFIBUS from GSD version/GSD revision | One GSD file each, Revision 3 and 5 and higher |
● PROFINET from GSD version/GSD revision | V2.3 |
Operating mode | |
● Switching between operating modes in RUN | Yes; For module version 32 I/20 Q, it is possible to dynamically switch between 25 user data variants, 23 of which are pre-defined and 2 of which can be defined by the specific user |
● Cyclic measured value access | Yes |
● Acyclic measured value access | Yes |
● Fixed measured value sets | Yes |
● Freely definable measured value sets | Yes; For cyclic and acyclic measured value access |
CiR - Configuration in RUN | |
Reparameterization possible in RUN | Yes |
Calibration possible in RUN | Yes |
Installation type/mounting | |
Mounting position | any |
Supply voltage | |
Rated value (DC) | 24 V |
permissible range, lower limit (DC) | 19.2 V |
permissible range, upper limit (DC) | 28.8 V |
Input current | |
Current consumption (rated value) | 12.5 mA |
Current consumption, max. | 17 mA |
Power loss | |
Power loss, typ. | 400 mW; 3x 230 V AC |
Address area | |
Address space per module | |
● Inputs | 256 byte |
● Outputs | 20 byte |
Hardware configuration | |
Automatic encoding | Yes |
● Mechanical coding element | Yes |
● Type of mechanical coding element | type C |
Selection of BaseUnit for connection variants | |
● 2-wire connection | BU type U0 |
Time of day | |
Operating hours counter | |
● present | Yes |
Analog inputs | |
Cycle time (all channels), typ. |
Similar products:
Siemens ET 200SP, F-AI 4xU 0..10V HF; 6ES7136-6AB00-0CA1
SIMATIC DP, electronics module ET 200SP, F-AI 4xU 0..10V HF, fail-safe analog inputs, up to PL E (ISO 13849), up to SIL 3 (IEC 61508)
-
(Out of stock)
Price on request
Siemens ET 200SP AI 2 X SG 4-/6-WIRE HS; 7MH4134-6LB00-0DA0
SIMATIC ET 200SP, ANALOG INPUT MODULE, AI 2 X SG 4-/6-WIRE HIGH SPEED, FITS TO BU-TYPE A0, COLOR CODE CC00, CHANNEL DIAGNOSIS, 28/16BIT, +/-0,05%, FOR STRAIN GAUGE
-
(Out of stock)
Price on request
Siemens ET 200SP HA, EX-AI 2xI 2-WIRE HART; 6DL1134-6TB00-0HX1
SIMATIC ET 200SP HA, ET 200SP, analog ex-i HART input module, Ex-AI 2xI 2-Wire HART, suitable for BaseUnit type X1, channel diagnostics, 16bit, +/-0.3%
-
(Out of stock)
Price on request
Siemens ET 200SP, AI 4xRTD/TC 2-/3-/4-Wire HF; 6ES7134-6JD00-0CA1
SIMATIC ET 200SP, Analog input module, AI 4xRTD/TC High Feature, suitable for BU type A0, A1, Color code CC00, channel diagnostics, 16 bit, +/-0.1%, 2-/3-/4-wir
-
(Out of stock)
Price on request
Siemens ET 200SP, AI 4xU/I 2-Wire ST, PU 1; 6ES7134-6HD01-0BA1
SIMATIC ET 200SP, ANALOG INPUT MODULE, AI 4XU/I 2-WIRE STANDARD, PACKING UNIT: 1 PIECE, FITS TO BU-TYPE A0, A1, COLOR CODE CC03, MODULE DIAGNOSIS, 16BIT, +/-0,3
-
(Out of stock)
Price on request
Siemens ET 200SP, AI 2xI 2-/4-Wire ST, PU 1; 6ES7134-6GB00-0BA1
SIMATIC ET 200SP, Analog input module, AI 2xI 2-/4-wire Standard, Pack quantity: 1 unit, suitable for BU type A0, A1, Color code CC05, Module diagnostics, 16 bi
-
(Out of stock)
18.203,76