Siemens F-TM StepDrive ST; 6BK1136-6SB00-0BU0
SIMATIC F-TM StepDrive ST, drive controller for stepper motors in the safety extra low voltage range, 24 to 48 V DC power supply of the drive, output current 5 A,...
Price on request
| SIMATIC F-TM StepDrive ST, drive controller for stepper motors in the safety extra low voltage range, 24 to 48 V DC power supply of the drive, output current 5 A, for SIMATIC ET 200SP, STO hardwired |
| General information | |
| Product type designation | F-TM StepDrive ST |
| HW functional status | V1.0 |
| Firmware version | V1.0 |
| ● FW update possible | Yes |
| Product description | control of stepper motors |
| usable BaseUnits | BU type U0 |
| Product function | |
| ● I&M data | Yes |
| ● Isochronous mode | No |
| ● Four-quadrant operation | Yes |
| ● Speed control with encoder | No |
| ● Speed control without encoder | No |
| ● Safety Functions | Yes; Drive controller with hardwired STO |
| Protection function | |
| ● Undervoltage protection | Yes |
| ● Overvoltage protection | Yes |
| ● Overload protection | Yes |
| ● Ground-fault protection | No |
| ● Short-circuit protection | Yes |
| Installation type/mounting | |
| Type of ventilation | Convection cooling |
| Supply voltage | |
| Design of the power supply | 24 ... 48 V DC, SELV / PELV |
| permissible range, lower limit (DC) | 16.8 V |
| permissible range, upper limit (DC) | 57.6 V |
| Input current | |
| Current consumption (rated value) | 6 A |
| Current consumption, max. | 10 A |
| Current consumption for the electronics, max. | 0.1 A; at 24 V |
| Inrush current, max. | 25 A; at 24 V |
| output voltage / header | |
| Rated value, min. | 24 V |
| Rated value, max. | 48 V |
| Output current | |
| Current output (rated value) | 5 A |
| Output current, max. | 10 A |
| Output frequency | 1 000 Hz |
| Encoder supply | |
| Number of outputs | 1 |
| 5 V encoder supply | |
| ● 5 V | Yes |
| ● Short-circuit protection | Yes |
| ● Output current, max. | 150 mA |
| Power | |
| DC power consumption | 300 W; At 50 V |
| Power loss | |
| Power loss, typ. | 3.5 W |
| Digital inputs | |
| Number of digital inputs | 1; input for message signal |
| Number of safety inputs | 1; For STO, antivalent (2-pin) - 24 V DC |
| Encoder | |
| Connectable encoders | |
| ● Incremental encoder (symmetrical) | Yes; up to 500 Hz per channel |
| Interrupts/diagnostics/status information | |
| Alarms | |
| ● Diagnostic alarm | Yes |
| ● Hardware interrupt | No |
| Diagnoses | |
| ● Monitoring the supply voltage | Yes |
| ● Wire-break | Yes |
| ● Short-circuit | Yes |
| ● Group error | Yes |
| Diagnostics indication LED | |
| ● RUN LED | Yes |
| ● ERROR LED | Yes |
| Integrated Functions | |
| Position detection | |
| ● Incremental acquisition | Yes |
| ● Absolute acquisition | No |
| Potential separation | |
| Potential separation channels | |
| ● between the channels and backplane bus | Yes |
| Isolation | |
| Isolation tested with | |
Similar products:
Siemens ET 200SP, TM Pulse 2x24V; 6ES7138-6DB00-0BB1
SIMATIC ET 200SP, TM Pulse 2x24V PWM and pulse output 2 channels 2 A for proportional valves and DC motors
-
(Out of stock)
Price on request
Siemens SIWAREX WP321 WEIGHING ELECTRONIC; 7MH4138-6AA00-0BA0
SIWAREX WP321 WEIGHING ELECTRONIC (1 CHANNEL) FOR STRAIN GAUGE LOAD CELLS / FULL BRIDGES (1-4 mV/V) FOR SIMATIC ET200SP, FITS to BU-TYPE A0, RS485- INTERFACE FOR
-
(Out of stock)
Price on request
Siemens ET 200SP TM SIWAREX WP341 HF; 7MH4138-6CA00-0CU0
SIMATIC ET 200SP, TM SIWAREX WP341 HF, weighing module for conveyor belt scales and solids flowmeters, 3xDI, 3xDQ, 1xRS485, 1xEthernet, 1x LC (1-4mV/V)
-
(Out of stock)
Price on request
Siemens ET 200SP TM SIWAREX WP351 HF; 7MH4138-6BA00-0CU0
SIMATIC ET 200SP, TM SIWAREX WP351 HF, verifiable weighing module for automatic dosing-, filling-, checking- and totalizing scales, 3xDI, 3xDQ, 1xCI,1xRS485, 1xEthernet,
-
(Out of stock)
Price on request
Siemens ET 200SP, TM PTO 2x24V; 6ES7138-6EB00-0BA0
SIMATIC ET 200SP, TM PTO 2x24 V, interface module for stepper drives, 2 channels pulse train output, PTO: 24 V, 2 DI, 1 DQ 24 V DC per channel, suitable for BU type
-
(Out of stock)
Price on request
Siemens ET 200SP, TM Count 1x24V; 6ES7138-6AA01-0BA0
SIMATIC ET 200SP, TM count 1x 24 V Counter module, 1 channel for 24 V incremental encoder or pulse encoder, 3 DI, 2 DQ Suitable for BU type A0, packing quantity:
-
(Out of stock)
Price on request